橡塑保温管施工的时候要多注意一些相关事项,才能让整个工程质量得到保障,下面 华美橡塑保温厂家就来讲讲橡塑保温管施工的十个基本步骤。
During the construction of rubber and plastic insulation pipe, more attention should be paid to some related matters to ensure the quality of the whole project. Now Huamei Rubber and Plastic Insulation Factory will talk about the ten basic steps of rubber and plastic insulation pipe construction.
1、使用一把短而硬的毛刷。
1. Use a short stiff brush.
2、将材料两端的粘结面涂上一层薄薄的、均匀的胶水。
2. Apply a thin and uniform layer of glue to the bonding surface at both ends of the material.
3、当在有压力的情况下连接两材料时,不必等到胶水干化,采用湿粘接法,先将材料放置在安装处,在材料的接口处涂上胶水,正确调整两材料的位置,很快就会按你设计的位置粘接牢固。
3. When connecting two materials under pressure, it is not necessary to wait for the glue to dry. Instead, use the wet bonding method. First place the materials at the installation site, apply glue to the interface of the materials, adjust the position of the two materials correctly, and the two materials will be firmly bonded according to your design position soon.
4、使用之前摇动容器,使胶水均匀,再实际安装中,用小罐胶水,以防止其挥发得太快,如有必要,可将大罐的倒入小罐中使用,不用时将罐口密封。
4. Shake the container before use to make the glue even. In the actual installation, use small cans of glue to prevent it from volatilizing too quickly. If necessary, pour large cans into small cans for use, and seal the tank mouth when not in use.
5、粘接时只需将粘接口的两表面对准握紧一会儿即可。
5. When bonding, just align the two surfaces of the bonding interface and hold it tightly for a while.
6、如果放置时间太长,以致两接面压在一起时不具粘性时,那么请重复步骤2—6。
6. If the storage time is too long, so that the two joint surfaces are not sticky when pressed together, repeat steps 2-6.
7、通常情况,每公斤橡塑胶水可涂抹两平米粘合面。
7. Generally, each kilogram of rubber plastic glue can be applied to two square meters of bonding surface.
8、通常,胶水不能在5℃以下使用,当在5℃—10℃的环境下工作时,请将胶水放置在温度为20℃的室内,需使用时取出。
8. Generally, the glue cannot be used below 5 ℃. When working at 5 ℃ - 10 ℃, please place the glue indoors at 20 ℃ and take it out when necessary.
9、胶水的自然干化时间﹡为3—10分钟,时间的长短取决于胶水的等级、大气的温度和湿度,一般应遵循:环境温度越高,相对湿度越大,介质温度越低,管道直径越大等材料就应越厚;裸露时间超过20分钟无效。
9. The natural drying time of glue * is 3-10 minutes. The time depends on the grade of glue, the temperature and humidity of the atmosphere. Generally, the higher the ambient temperature is, the greater the relative humidity is, the lower the medium temperature is, and the thicker the pipe diameter is; It is invalid if the exposure time exceeds 20 minutes.
10、检查胶水和保护铁管的防锈漆间是否粘接牢固。
10. Check whether the glue is firmly bonded to the anti rust paint of the protective iron pipe.
橡塑保温管施工的十个基本步骤就讲解完毕了,您对此有什么不懂得地方欢迎来我们网站 http://www.hmbwcl.cn进行咨询吧!
The ten basic steps of rubber and plastic insulation pipe construction have been explained. If you don't know anything about this, please come to our website http://www.hmbwcl.cn Consult!
上一篇: 存放橡塑保温材料的三个要点
下一篇: 玻璃棉的生产工艺适用性如何?